Anstek Solutions

Wilcoxon’s PCC420A series sensors provide a 4-20 mA output proportional to vibration, allowing for continuous trending of overall machine vibration. This trend data alerts users to changing machine conditions and helps guide maintenance in prioritizing the need for service. The choice of RMS or peak output allows you to choose the sensor that best fits your requirements.

Features:

• High sensitivity
• Ultra low-noise electronics for clear signals at very low vibration levels
• Low pass filtered to eliminate high frequencies
• Optimized for 15V supply
• ESD protection

Features:

• Clear signals at low vibration levels
• Extended low frequency response
• Improved signal to noise ratio versus other general purpose accelerometers
• High sensitivity
• Hazardous area certified models available

Features:

• Ideal for power generation applications
• Rapid shock recovery
• Hermetically sealed
• Case-base isolation min 6 kV
• EMI-protected

Wilcoxon’s PCC420V series sensors provide a 4-20 mA output proportional to velocity vibration, allowing for continuous trending of overall machine vibration. This trend data alerts users to changing machine conditions and helps guide maintenance in prioritizing the need for service. The choice of RMS or peak output allows you to choose the sensor that best fits your requirements.

Explosion-proof, 4-20mA output proportional to peak velocity, 2.0 in/sec full-scale measurement range, ±5% sensitivity tolerance at full scale

Features:

• Explosion proof certification
• 4-20 mA output, peak velocity
• Corrosion resistant
• Hermetic seal
• ESD, overload, and reverse wiring protection

HART-enabled, field-configurable 4-20mA velocity sensor, certified for Class I, Div 2/Zone 2 hazardous areas, three independently programmable vibration bands, MIL-C-5015 connector, 0.5-5.0 in/sec peak (user-configured)

Features:

• HART protocol for digital communication with plant infrastructure
• 3 independently programmable vibration bands
• Enables single or multi-drop loop installations
• Certified for use in Class 1, Div 2/Zone 2 hazardous areas

Side exit, triaxial, case isolated, 1/4-28 captive screw, 4 pin Bendix #PC01A-8-4P (p/n R9W), 100 mV/g, ±10% sensitivity tolerance

Features:

• Rugged design
• Easy to mount
• Fast and consistent data collection
• Reduced wiring for permanent installations

HART-enabled, field-configurable 4-20mA digital velocity sensor with three independently programmable vibration bands, M12 connector, 0.5-5.0 in/sec peak (user-configured)

Features:

• HART protocol for digital communication with plant infrastructure
• 3 independently programmable vibration bands
• Enables single or multi-drop loop installations
• Hazardous area certified models available

Features:

• Operating temperature range up to 260°C
• Industrial ruggedness
• Charge output
• Ground isolated

Features:

• Superior broadband frequency
• Extended low-end frequency response down to 0.2 Hz
• High sensitivity
• Rugged design, hermetic seal
• Case isolation

Features:

• Ultra low power consumption (300 µW)
• Fast BOV settling time of <10 ms
• Operates down to 3V
• Hermetically sealed
• Comes with the industry popular M12 connector

Features:

• Wide dynamic range
• Compact construction to fit in tight spaces
• Wide frequency range up to 25 kHz

Features:

• Senses both acceleration and temperature
• Rugged design
• Hermetic seal
• ESD, overload and reverse wiring protection

Features:

• Senses both acceleration and temperature
• Rugged design
• Hermetic seal
• ESD protection

Top exit, extremely low frequency (0.1 Hz low end) accelerometer, MIL-C-5015 connector, case isolated, 100 mV/g, ±5% sensitivity tolerance.

Features:

• Extended low frequency response
• Hermetically sealed
• High sensitivity
• Clear signals at low vibrations
• Available with 100, 250 or 500 mV/g sensitivity

Features:

• High sensitivity
• Ultra low-noise electronics for clear signals at very low vibration levels
• Low pass filtered to eliminate high frequencies
• Optimized for 15V supply
• ESD protection